1.1 这些测试方法规定了用于测试和评估外载力量训练设备、力量训练台和外部重量存储设备是否符合规范的程序和仪器 F3105 . 将评估设计和操作参数。在可能和适用的情况下，将使用和参考其他认可机构的认可测试方法。 1.2 要求- 该设备应根据本试验方法或试验方法进行试验 F2571 对于以下所有参数: 1.2.1 稳定性 1.2.2 边缘和拐角锐度， 1.2.3 管端， 1.2.4 陷阱和夹点， 1.2.5 重量圆盘保持力， 1.2.6 调节和锁定机制的功能， 1.2.7 训练后负重， 1.2.8 装载后的储存重量， 1.2.9 停止高度验证， 1.2.10 停止负载下降测试， 1.2.11 杠铃钩尺寸， 1.2.12 吊钩负荷下降试验， 1.2.13 杠铃支架/框架冲击试验， 1.2.14 固有负载， 1.2.15 外部荷载， 1.2.16 耐久荷载，以及 1.2.17 文件和警告验证。 1.3 本标准并非旨在解决与其使用相关的所有安全问题（如有）。本标准的用户有责任在使用前制定适当的安全、健康和环境实践，并确定监管限制的适用性。 1.4 本国际标准是根据世界贸易组织技术性贸易壁垒（TBT）委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认标准化原则制定的。 ====意义和用途====== 4.1 本文件旨在提供有效且可重复的测试方法，用于评估根据制造商规范组装和维护的外载力量训练设备、力量训练台和外部重量存储设备。 结合规范使用这些试验方法 F3105 旨在最大限度地提高设备设计的可靠性，并减少因设计缺陷而导致严重伤害的风险。

1.1 These test methods specify procedures and apparatus used for testing and evaluating Externally Loaded Strength Training Equipment, Strength Training Benches and External Weight Storage Equipment for compliance to Specification F3105 . Both design and operational parameters will be evaluated. Where possible and applicable, accepted test methods from other recognized bodies will be used and referenced. 1.2 Requirements— This equipment is to be tested in accordance with this test method or Test Methods F2571 for all of the following parameters: 1.2.1 Stability, 1.2.2 Edge and corner sharpness, 1.2.3 Tube ends, 1.2.4 Entrapment and pinch points, 1.2.5 Weight disc retention, 1.2.6 Function of adjustments and locking mechanisms, 1.2.7 Training weight post loading, 1.2.8 Storage weight post loading, 1.2.9 Stop height verification, 1.2.10 Stop load drop test, 1.2.11 Barbell hook dimensions, 1.2.12 Catch hook load drop test, 1.2.13 Barbell support/frame impact test, 1.2.14 Intrinsic loading, 1.2.15 Extrinsic loading, 1.2.16 Endurance loading, and 1.2.17 Documentation and warnings verification. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 4.1 The purpose of this document is to provide valid and repeatable test methods for the evaluation of Externally Loaded Strength Training Equipment, Strength Training Benches and External Weight Storage Equipment assembled and maintained according to the manufacturer's specifications. Use of these test methods in conjunction with Specification F3105 is intended to maximize the reliability of the equipment’s design and reduce the risk of serious injury resulting from design deficiencies.