BS EN 1993-1-3:2006给出了冷成型构件和板材的设计要求。它适用于 由涂层或未涂层的热轧或冷轧薄板或带材制成的冷成型钢制品，具有 通过冷轧成形或压力制动等工艺进行冷成形。它也可用于在施工阶段设计复合钢和混凝土板的压型钢板，见EN 1994。这个 EN 1090中涵盖了冷成型构件和板材制成的钢结构的施工。注:本部分的规则补充了EN 1993-1其他部分的规则。还给出了使用钢板作为结构隔板的应力蒙皮设计方法。本部分不适用于供应给EN的冷成型圆形和矩形结构空心型材 10219，参考EN 1993-1-1和EN 1993-1-8。BS EN 1993-1-3:2006给出了计算设计和试验辅助设计的方法。测试方法 通过计算进行的设计仅适用于材料特性和几何比例的规定范围内 有足够的经验和测试证据。这些限制不适用于辅助设计 测试。BS EN 1993-1-3:2006不包括在执行和维护期间测试负载的负载安排。本标准中给出的计算规则仅在冷成型构件的公差 符合EN 1090-2交叉参考:EN 1993-1-1EN 1993-1-2EN 1993-1-4EN 1993-1-5EN 1993-1-6EN 1993-1-7EN 1993-1-8EN 1993- 1-9EN 1993-1-10EN 1993-1-11EN 1993-1-12EN 10002-1EN 10025-1EN 10025-2EN 10025-4EN 10025-5EN 10143EN 10149-2EN 10204EN 10268EN 10292EN 10326EN 10327EN ISO 12944-2ISO 12944-2:1998EN 1090-2EN 1994EN ISO 1478EN ISO 2702EN ISO 7049EN ISO 10684ISO 4997EN 508-1FEM 10.2.02取代了被撤销并部分取代BS 5950-5:1998的DD ENV 1993-1-3:2001，BS 5950-6:1995和BS 5950-9:1994。

BS EN 1993-1-3:2006 gives design requirements for cold-formed members and sheeting. It applies to cold-formed steel products made from coated or uncoated hot or cold rolled sheet or strip, that have been cold-formed by such processes as cold-rolled forming or press-braking. It may also be used for the design of profiled steel sheeting for composite steel and concrete slabs at the construction stage, see EN 1994. The execution of steel structures made of cold-formed members and sheeting is covered in EN 1090.NOTE: The rules in this part complement the rules in other parts of EN 1993-1.Methods are also given for stressed-skin design using steel sheeting as a structural diaphragm.This part does not apply to cold-formed circular and rectangular structural hollow sections supplied to EN 10219, for which reference should be made to EN 1993-1-1 and EN 1993-1-8.BS EN 1993-1-3:2006 gives methods for design by calculation and for design assisted by testing. The methods for design by calculation apply only within stated ranges of material properties and geometrical proportions for which sufficient experience and test evidence is available. These limitations do not apply to design assisted by testing.BS EN 1993-1-3:2006 does not cover load arrangement for testing for loads during execution and maintenance.The calculation rules given in this standard are only valid if the tolerances of the cold formed members comply with EN 1090-2Cross References:EN 1993-1-1EN 1993-1-2EN 1993-1-4EN 1993-1-5EN 1993-1-6EN 1993-1-7EN 1993-1-8EN 1993-1-9EN 1993-1-10EN 1993-1-11EN 1993-1-12EN 10002-1EN 10025-1EN 10025-2EN 10025-3EN 10025-4EN 10025-5EN 10143EN 10149-2EN 10149-3EN 10204EN 10268EN 10292EN 10326EN 10327EN ISO 12944-2ISO 12944-2:1998EN 1090-2EN 1994EN ISO 1478EN ISO 1479EN ISO 2702EN ISO 7049EN ISO 10684ISO 4997EN 508-1FEM 10.2.02Replaces DD ENV 1993-1-3:2001 which is withdrawn and partially replaces BS 5950-5:1998, BS 5950-6:1995 and BS 5950-9:1994.