1.1 本试验方法包括确定液体是否符合政府法规、规范或买卖双方约定的闭杯闪点要求。 1.2 本试验方法仅限于0至110°C（32至230°F）的温度范围。 1.3 以英寸-磅为单位的数值应视为标准值。括号中给出的值是到国际单位制的数学转换，仅供参考，不被视为标准值。 1.4 警告- 许多监管机构已将汞指定为一种危险物质，可导致严重的医疗问题。汞或其蒸汽已被证明对健康有害，并对材料具有腐蚀性。处理汞和含汞产品时要小心。有关更多信息，请参阅适用的产品安全数据表（SDS）。当地或国家法律禁止销售汞或含汞产品，或两者兼有。用户必须确定其所在地销售的合法性。 1.5 本标准用于测量和描述材料、产品或组件在受控条件下对热量和火焰的响应，但其本身并不包括在实际火灾条件下对材料、产品或组件进行火灾危险或火灾风险评估所需的所有因素。 1.6 本标准并非旨在解决与其使用相关的所有安全问题（如有）。本标准的用户有责任在使用前制定适当的安全、健康和环境实践，并确定监管限制的适用性。 1.7 本国际标准是根据世界贸易组织技术性贸易壁垒（TBT）委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认标准化原则制定的。 ====意义和用途====== 5.1 该试验方法确保在进行闪蒸试验之前，通过在平衡条件下使用标准闭杯，样品上方的空气/蒸汽空间已达到蒸汽的饱和浓度。 蒸汽的饱和浓度将在液体和冷却器装置盖之间的某个温度下达到。然而，在规定温度下保持至少10分钟后，该温度将接近试样的温度。本试验方法不提供实际闪点的测定，而仅提供试样是否在规定温度下闪点。

1.1 This test method covers the determination of whether a liquid complies with the closed-cup flash point requirements in government regulations, or in specifications, or as agreed between the purchaser and the seller. 1.2 This test method is limited to a temperature range between 0 and 110°C (32 and 230°F). 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 Warning— Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location. 1.5 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 5.1 This test method ensures that before the flash test is run the air/vapor space above the specimen has attained a saturation concentration of vapor by using standard closed cups under equilibrium conditions. The saturation concentration of the vapors will be attained at some temperature between that of the liquid and the cooler apparatus lid. However, this temperature will be close to the temperature of the specimen after it has been maintained at the specified temperature for at least a 10-min period. This test method does not provide for the determination of the actual flash point but only whether a specimen does or does not flash at a specified temperature.