Metric taper external and mating parallel internal screw threads - Dimensions, tolerances and inspection
公制外锥螺纹和配套内平行螺纹.第1部分:公称尺寸、极限偏差、尺寸极限和检验

1997-06-01

ISO metric trapezoidal screw threads; gauging of external and internal threads; gauge dimensions and design features
ISO公制梯形螺纹；测量外螺纹和内螺纹；量规尺寸和设计特点

1985-02-01

55°密封管螺纹量规 第1部分：用于检验圆柱内螺纹与圆锥外螺纹
Gauges for pipe threads with 55 degree thread angle where pressure-tight joints are made on the threads - Part 1:Verification of parallel internal and taper external threads

2008-06-25

Geometrical product specifications (GPS) - Gauges for internal and external ISO metric screw threads - Overview of types, marking and application
产品几何技术规范（GPS）.ISO公制螺纹量规.内螺纹和外螺纹的量规；调查、题字、标记、应用

2001-12-01

ISO general purpose metric screw threads. Tolerances-Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing
ISO通用公制螺纹 公差

2021-07-26

ISO general purpose metric screw threads. Tolerances-Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing
ISO通用公制螺纹 公差

2021-07-26

ISO general purpose metric screw threads — Tolerances — Part 4: Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing
Iso通用公制螺纹螺纹 - 公差 - 第4部分:热浸镀锌外螺纹的尺寸限制 与内螺纹螺纹配合 镀镍后具有公差位置H或G

2021-07-06

ISO general purpose metric screw threads -- Tolerances -- Part 4: Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing
ISO通用米制螺纹公差第4部分:镀锌后与公差位置为H或G的内螺纹配合的热浸镀锌外螺纹的尺寸限制

2001-01-01

ISO general purpose metric screw threads -- Tolerances -- Part 5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing
ISO通用米制螺纹公差第5部分:镀锌前最大公差位置为h的热浸镀锌外螺纹与内螺纹配合的尺寸限制

2001-01-01

ISO general purpose metric screw threads — Tolerances — Part 5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing
ISO通用公制螺纹——公差SPART 5:与热浸镀锌外螺纹配合的内螺纹尺寸限制 镀锌前最大公差位置为h

1998-12-20

Основные нормы взаимозаменяемости. Резьбы метрические ИСО общего назначения. Допуски. Предельные размеры внутренних резьб, сопрягаемых с горячеоцинкованными наружными резьбами, соответствующими до нанесения покрытия полям допусков с основными отклонениями до h включительно
互换性的基本规范 ISO通用公制螺纹 公差 内螺纹尺寸的限制与热镀锌外螺纹配合 镀锌前最大公差位置h

2015-08-27

ISO general purpose metric screw threads — Tolerances — Part 5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing — Amendment 1
ISO通用米制螺纹.公差.第5部分:镀锌前最大公差位置为h的热浸镀锌外螺纹与内螺纹配合的尺寸限制.修改件1

2021-07-06

ISO general purpose metric screw threads - Tolerances - Part 4: Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing (ISO 965-4:1998)
ISO通用米制螺纹公差第4部分:镀锌后与公差位置为H或G的内螺纹配合的热浸镀锌外螺纹的尺寸限制

2002-05-01

ISO general purpose metric screw threads - Tolerances - Part 5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing (ISO 965-5:1998)
ISO通用米制螺纹公差第5部分:镀锌前最大公差位置为h的热浸镀锌外螺纹与内螺纹配合的尺寸限制

2002-05-01

ISO metric coarse and fine pitch screw threads for interference fits in aluminium cast alloys with diameters from 5 mm to 16 mm - Gauges for internal and external threads
ISO公制螺纹；铝铸造合金过盈配合用粗螺距螺纹和细螺距螺纹；标称直径为5mm至16mm；内外螺纹量规

1993-07-01

Draft Document - ISO general purpose metric screw threads - Tolerances - Part 4: Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing (ISO/DIS 965-4:2020); Text in German and English
文件草稿ISO通用米制螺纹公差第4部分:镀锌后与公差位置为H或G的内螺纹配合的热浸镀锌外螺纹的尺寸限制；德语和英语文本

2021-01-01

Draft Document - ISO general purpose metric screw threads - Tolerances - Part 5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing - Amendment 1 (ISO 965-5:1998/DAM 1:2020); Text in German and English
文件草案.ISO通用公制螺纹.公差.第5部分:镀锌前最大公差位置为h的热浸镀锌外螺纹与内螺纹配合的尺寸限制.修改件1（ISO 965-5-1998/DAM 1:2020）；德语文本

2021-01-01