BS ISO 19859:2016规定了设备的最低技术和文件要求 发电用燃气轮机系统的评估和采购。 它适用于陆上和海上应用的简单循环和联合循环燃气轮机， 如适用。它也适用于热电联产中使用的燃气轮机（见ISO 11086:1996，附录B）。本范围包括燃气轮机和发电机的测试。 它不适用于用于所有类型推进的燃气轮机，包括飞机、移动驳船、， 浮式生产船、船舶推进应用和微型涡轮机。 本国际标准定义了燃气轮机发电的要求 基于现有公认ISO和IEC标准内容的国际视角 最大程度上是实用的。尽管如此，业内公认的是，其他规范或标准 使用，其中一些包含在本国际标准的文本中。使用其他类似的 只要有适当且可接受的要求，规范和标准是允许的， 实现了功能设计和安全性，双方就其使用达成了一致 买方和承包商，并适当记录此类使用。 应考虑按照以下等级顺序应用/使用标准: 国际的地区的国家的地方的本国际标准确定了买方和承包商的要求 归因于燃气轮机发电机组的设计和采购。 定义的要求适用于供应范围，除非排除在外，包括 发电机组内的以下设备和相关选定选项如下所示:燃气轮机机组；负载联轴器和离合器（如适用）；进气系统；排气系统；燃料设备； 控制设备；电气设备；其他辅助系统，包括启动、润滑、盘车、压缩机清洗、管道工程、， 排水管和通风口；防火和气体保护；冷却水设备。如果适用于燃气轮机组件的完整性，接口和适用设计 要求包括与发电设备连接的设备、公用设施和用品 包裹交叉引用:ISO 128-1ISO 1461ISO 1940-1:2003ISO 2314:2009ISO 2409ISO 2533ISO 2592ISO 2909ISO 2954ISO 3016ISO 3104ISO 3448ISO 3675ISO 3746ISO 3977-1ISO 3977-3:2004ISO 3977-4:2002ISO 3977-8ISO 3977-9:1999ISO 4261ISO 4263- 4:2009 2009年ISO 851:1 ISO 851:1 1 ISO 851:1 1 ISO 851:1 ISO 851 1:1 1 ISO 851 1:1 ISO 851:1 ISO 851 1 1:2 ISO 851 1:2 2 ISO 851 1:2 2 ISO 854-1 1 1:2 2）2 2:2 2 2 ISO 851:2 2 2:2 2 2 2:1 1 1:2）2:2:2）2 2:1 1:2:1 1 1:2:2 2:2:2 2:2:2:2:2:2:2 2 2 2 2:2:1 1 1 1 1 1 1:1:1 1 1 1 1:1:2 2 2 2 2:1:2 2 2 2 2 2 2 2）2:1:1）2 2 2 2 2 2）2）2（2（2）2（2（2）2（2）2）2）2）2）2）2（2（2）2（2）2）2）2）2 SO 12151-2ISO 12944-1ISO 12944-2:1998 ISO 12944-4ISO13691ISO 13938-1ISO 14122-1ISO 14122-2:2001ISO 14122-3ISO 14122-4ISO 14123-1ISO 14691ISO 14713-2ISO 15649ISO 16276-2ISO 18752ISO 19840ISO 19860:2005ISO 21789:2009ISO 21940-13ISO 21940-31ISO 21940-32ISO 22266-1ISO 80000-1IEC 60034-1IEC 60034-3: 2011年10 10-10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 TR 61000-5-1IEC/TR 61000-5-2IEC 61140IEC 61643-12IEC 61672-1IEC61786IEC 61918IEC 61936-1IEC 62040-1IEC 62040-2IEC 62305-1IEC 62305-4IEC 82079-1EN 779EN 1822-1EN 1822-5EN 1837EN 1838EN 1997-1EN 13284-1:2001EN 13480-1EN 15259-1:2007EN 50160EN 50272-2EN 5052IEEE C50。13IEEE C95。3IEEE 762:2006AGMA 6011-I03AGMA 6011- J14AGMA 6123-B06ASHRAE 52.2API 613API 670ASME B31。1中小企业B31。3SME PTC 22ASTM D3786NAS 1638NEMA MG1NFPA 70NFA购买本文件时提供的所有当前修订版均包含在购买本文件中。

BS ISO 19859:2016 specifies the minimum technical and documentation requirements for the evaluation and procurement of gas turbine systems for electrical power generation. It applies to simple cycle and combined cycle gas turbines for both onshore and offshore applications, where applicable. It also applies to gas turbines used in cogeneration (see ISO 11086:1996, Annex B).Testing of the gas turbine in combination with a generator is included in the scope. It is not applicable to gas turbines used for all types of propulsion including aircraft, mobile barges, floating production vessels and marine propulsion applications and microturbines.This International Standard defines the requirements for gas turbine power generation from an international perspective based on the content of existing, recognized ISO and IEC standards to the greatest extent practical. Nonetheless, it is recognized that within the industry other codes or standards are used, some of which are included in the text of this International Standard. The use of other such codes and standards is permissible provided an appropriate and acceptable level of requirements, functional design and safety is achieved and agreement has been reached for their use between the Purchaser and Contractor and such use is suitably documented.Consideration should be given to applying/using standards in the following hierarchical order: international; regional; national; local.This International Standard identifies the requirements for both the Purchaser and Contractor attributable to the design and procurement of a gas turbine power generation package. The defined requirements apply to the scope of supply, except where excluded, encompassing the following equipment and the associated selected options, located within the power generation package, listed below:gas turbine package;load shaft coupling and clutch, as applicable;air inlet system;exhaust system;fuel equipment;control equipment;electrical equipment;additional auxiliary systems, including starting, lubrication, barring, compressor wash, pipework, drains and vents;fire and gas protection;cooling water equipment.Where applicable to the integrity of the gas turbine package, the interface and applicable design requirements are included for equipment, utilities and supplies that interface with the power generation package.Cross References:ISO 128-1ISO 1461ISO 1940-1:2003ISO 2314:2009ISO 2409ISO 2533ISO 2592ISO 2909ISO 2954ISO 3016ISO 3104ISO 3448ISO 3675ISO 3746ISO 3977-1ISO 3977-3:2004ISO 3977-4:2002ISO 3977-8ISO 3977-9:1999ISO 4261ISO 4263-1ISO 4406ISO 4407ISO 5167-1ISO 6247ISO 6336-1ISO 6743-5ISO 6976ISO 7919-4:2009ISO 8501-1ISO 8501-2ISO 8501-3ISO 8502ISO 8504-1ISO 9120ISO 9223ISO 9614-1ISO 9614-2ISO 9951ISO 10380ISO 10396ISO 10441:2007ISO 10494ISO 10816-2ISO 10816-3ISO 10816-4:2009ISO 10817-1ISO 11042-1ISO 11042-2ISO 11086:1996ISO 11204ISO 11342:1998ISO 12100ISO 12151-1ISO 12151-2ISO 12944-1ISO 12944-2:1998ISO 12944-4ISO 13691ISO 13938-1ISO 14122-1ISO 14122-2:2001ISO 14122-3ISO 14122-4ISO 14123-1ISO 14691ISO 14713-2ISO 15649ISO 16276-2ISO 18752ISO 19840ISO 19860:2005ISO 21789:2009ISO 21940-13ISO 21940-31ISO 21940-32ISO 22266-1ISO 80000-1IEC 60034-1IEC 60034-3:2010IEC 60034-5IEC 60038:2009IEC 60079-10-1IEC 60079-11IEC 60079-14:2013IEC 60146-1IEC 60204-1:2009IEC 60204-11IEC 60304IEC 60332IEC 60364-1IEC 60364-4-41IEC 60417IEC 60439IEC 60445IEC 60502IEC 60529:2013IEC 60757IEC 60896IEC 60947IEC 60947-7-1IEC 61000-2-2IEC 61000-2-4:2002IEC 61000-4-2IEC 61000-6-2IEC 61000-6-3IEC 61000-6-4IEC/TR 61000-5-1IEC/TR 61000-5-2IEC 61140IEC 61643-12IEC 61672-1IEC 61786IEC 61918IEC 61936-1IEC 62040-1IEC 62040-2IEC 62305-1IEC 62305-4IEC 82079-1EN 779EN 1822-1EN 1822-5EN 1837EN 1838EN 1997-1EN 13284-1:2001EN 13480-1EN 15259-1:2007EN 50160EN 50272-2EN 50522IEEE C50.13IEEE C95.3IEEE 762:2006AGMA 6011-I03AGMA 6011-J14AGMA 6123-B06ASHRAE 52.2API 613API 670ASME B31.1ASME B31.3ASME PTC 22ASTM D3786NAS 1638NEMA MG1NFPA 70NFAll current amendments available at time of purchase are included with the purchase of this document.