1.1 本试验方法使用记录恒定拉伸速率的拉伸试验机测量钩环接触（CRE）紧固件的剪切强度。 1.2 以英寸-磅为单位的数值应视为标准值。括号中给出的值是到国际单位制的数学转换，仅供参考，不被视为标准值。 1.3 本标准并非旨在解决与其使用相关的所有安全问题（如有）。本标准的用户有责任在使用前制定适当的安全、健康和环境实践，并确定监管限制的适用性。 1.4 本国际标准是根据世界贸易组织技术性贸易壁垒（TBT）委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认标准化原则制定的。 ====意义和用途====== 5.1 本试验方法测量了钩环接触紧固件的关键性能，这是此类设备用户感兴趣的。当平行于紧固件平面施加力时，这是一种确定分离阻力的方法。 5.2 如果使用本测试方法进行商业装运验收测试时，由于报告测试结果的差异而产生争议，买方和供应商应进行比较测试，以确定其实验室之间是否存在统计偏差。建议为调查偏差提供称职的统计协助。作为最低要求，双方应尽可能从大量相关类型的钩环中选取一组同质试样。 然后，应将试样以相同数量随机分配给每个实验室进行测试。两个实验室的平均结果应使用学生的 t -测试和双方在测试开始前选择的可接受概率水平。如果发现偏差，必须找到并纠正其原因，或者买方和供应商必须同意根据已知偏差解释未来的测试结果。

1.1 This test method measures the shear strength of hook and loop touch (CRE) fasteners using a recording constant rate of extension tensile testing machine. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 5.1 This test method gives a measure of a key property of hook and loop touch fasteners which is of interest to users of such devices. This is a means of determining the resistance to separation when forces are applied parallel to the plane of the fastener. 5.2 In the case of a dispute arising from differences in reported test results when using this test method for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens which are as homogenous as possible and which are from a lot of hook and loop of the type in question. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Student’s t -test and an acceptable probability level chosen by the two parties before the testing began. If a bias is found, either its cause must be found and corrected or the purchaser and the supplier must agree to interpret future test results in the light of the known bias.