1.1 本试验方法包括制备和测试实验室压实沥青混合料试样的程序，目的是测量水对铺路混合料抗拉强度的影响。本试验方法适用于本规范中沥青铺路混合料组成表中的致密混合料 D3515 该试验方法可用于评价水分在有或没有抗剥离添加剂的情况下的影响，抗剥离添加剂包括液体和粉状固体，如熟石灰或波特兰水泥。 1.2 括号中以国际单位制单位或英磅单位表示的值应单独视为标准值。每个系统中的值可能不完全等效；因此，每个系统必须独立于另一个系统使用，不能以任何方式组合值。1.3 本标准的正文参考了提供解释材料的注释和脚注。这些注释和脚注（不包括表格和图表中的注释和脚注）不应被视为标准的要求。 1.4 本标准并不旨在解决与其使用相关的所有安全性问题（如果有）。本标准的使用者有责任在使用前建立适当的安全、健康和环境实践并确定法规限制的适用性。 1.5 本国际标准是根据世界贸易组织技术性贸易壁垒（TBT）委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认的标准化原则制定的。======意义和用途====== 5.1 该测试方法可与混合料设计测试一起用于测试沥青混合料，以确定水分损害的可能性，确定抗剥离添加剂是否有效，并确定需要什么剂量的添加剂才能使有效性最大化。该测试方法也可用于测试植物中生产的混合物，以确定添加剂在田间施加的条件下的有效性。 附注1: 本标准产生的结果的质量取决于执行该程序的人员的能力以及所用设备的能力、校准和维护。符合规范标准的机构 D3666 通常被认为能够胜任和客观的测试、取样、检查等。本标准的使用者应注意符合规范 D3666 单独并不能完全确保可靠的结果。可靠的结果取决于许多因素；遵循规范的建议 D3666 或者一些类似的可接受的指南提供了评估和控制这些因素中的一些的方法。

1.1 This test method covers procedures for preparing and testing laboratory-compacted asphalt mixture specimens for the purpose of measuring the effect of water on the tensile strength of the paving mixture. This test method is applicable to dense mixtures such as those appearing in the Table for Composition of Bituminous Paving Mixtures in Specification D3515 . This test method can be used to evaluate the effect of moisture with or without antistripping additives including liquids and pulverulent solids such as hydrated lime or portland cement. 1.2 The values stated in either SI units or inch-pound units in brackets shall be regarded separately as standard. The values in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values in any way. 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 5.1 This test method can be used to test asphalt mixtures in conjunction with mixture design testing to determine the potential for moisture damage, to determine whether or not an antistripping additive is effective, and to determine what dosage of an additive is needed to maximize the effectiveness. This test method can also be used to test mixtures produced in plants to determine the effectiveness of additives under the conditions imposed in the field. Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.