1.1 本规范涵盖了空的和全木质夹板箱（以下简称木质夹板箱）的制造和封闭。这些箱子拟用作国内和海外装运一般材料和物资的容器，根据箱子类型不超过1000磅[454千克]（见 10.1 ). 1.2 木质夹板装运箱的性能取决于其制造组件和后续组装；因此，规定了反映不同性能的各种类型、类别、风格和处理。然而，本规范不包括所有大气、搬运、运输和储存条件下的木质夹板箱性能。 1.3 如果可接受并允许使用其他施工方法或技术（参见 5.1.17 )，由此产生的包装系统应具有与使用这些指定材料和程序产生的性能相同或更好的性能。实践中规定的适当分配周期 D4169 ，可用于制定比较程序和标准。 1.4 以英寸-磅单位或国际单位表示的数值应单独视为标准值。在文本中，国际单位显示在括号中。每个系统中规定的值不是精确的等价物；因此，每个系统必须相互独立使用。将两个系统的值合并可能会导致不符合标准。 看见 IEEE/ASTM SI 10 用于单位转换。 1.5 本标准并非旨在解决与其使用相关的所有安全问题（如有）。本标准的用户有责任在使用前制定适当的安全、健康和环境实践，并确定监管限制的适用性。 1.6 本国际标准是根据世界贸易组织技术性贸易壁垒（TBT）委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认标准化原则制定的。

1.1 This specification covers the fabrication and closure of empty and full wood-cleated, hereafter referred to as wood-cleated, panelboard boxes. These boxes are intended for use as containers for domestic and overseas shipment of general materials and supplies, not exceeding 1000 lb [454 kg] depending on box type (see 10.1 ). 1.2 Wood-cleated panelboard shipping box performance is dependent on its fabricated components and subsequent assembly; therefore, a variety of types, classes, styles, and treatments reflecting varied performance are specified. This specification, however, does not cover wood-cleated panelboard box performance under all atmospheric, handling, shipping, and storage conditions. 1.3 If the use of other construction methods or techniques is acceptable and permitted (see 5.1.17 ), the resulting packaging systems shall be of equal or better performance than would result from the use of these specified materials and procedures. The appropriate distribution cycle, specified in Practice D4169 , can be used to develop comparative procedures and criteria. 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. See IEEE/ASTM SI 10 for conversion of units. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.