1.1 本规范定义了锁条垫圈所需的性能，其中耐日光、耐候、耐火焰、耐氧化、负载下的永久变形和降低夹紧压力是首要要求。 附注1: 如果不与当地法规或条例相冲突，建筑师或专业工程师可以免除火焰传播的要求。 1.2 本说明书仅适用于“锁定”压缩类型的垫圈，有时称为“拉链”类型。 附注2: 墙的结构完整性和耐候性需要整个系统的合理设计和安装，垫圈只是其中的一个部件。 1.3 以SI单位表示的值应被视为标准。 1.4 试验方法 C1166 如本说明书中所引用的，应用于测量和描述材料、产品或组件在受控实验室条件下响应热和火焰的特性，并且不应用于描述或评价材料、产品或组件在实际火灾条件下的火灾危险或火灾风险。然而，该测试的结果可以用作火灾风险评估的要素，该评估考虑了与特定最终用途的火灾危险评估相关的所有因素。 1.5 以下注意事项仅适用于试验方法部分，章节 7 本说明书: 本标准并不旨在解决与其使用相关的安全性问题（如有）。本标准的使用者有责任在使用前建立适当的安全、健康和环境实践并确定法规限制的适用性。 1.6 对该标准有管辖权的委员会不知道其他组织发布的任何类似标准。1.7 本国际标准是根据世界贸易组织技术性贸易壁垒委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认的标准化原则制定的。

1.1 This specification defines the required properties of lock-strip gaskets where resistance to sunlight, weathering, flame, oxidation, permanent deformation under load, and diminution of gripping pressure are prime essentials. Note 1: The requirement of flame propagation may be waived by the architect or professional engineer when doing so does not conflict with local codes or ordinances. 1.2 This specification applies only to the “locking” compression type of gasket, sometimes referred to as the “zipper” type. Note 2: Structural integrity and weather-tightness of the wall requires the sound design and installation of the entire system of which the gasket is only one component. 1.3 The values stated in SI units are to be regarded as the standard. 1.4 Test Method C1166 , as referenced in this specification, should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use. 1.5 The following precautionary caveat pertains only to the test method portion, Section 7 , of this specification: This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.