BS EN 16905-4:2017规定了额定值和额定值的要求、试验方法和试验条件 以空气、水或盐水为热源的空调和热泵的性能计算 传输介质，当用于空间加热时，带有燃气吸热式发动机驱动压缩机， 冷却和制冷，以下简称“GEHP设备”。本欧洲标准仅适用于具有最大热量输入（基于净热量）的电器 值）在标准额定条件下不超过70 kW。本欧洲标准仅适用于I2H、I2E、I2Er、I2R、I2E（S）B、I2L、I2LL、I2LL、， I2E（R）B、I2ESi、I2E（R）、I3P、I3B、I3B/P、II2H3+、II2Er3+、II2H3B/P、II2L3B/P、II2E3B/P、II2ELL3B/P、II2L3P、II2H3P和II2Er3P 根据EN 437。本欧洲标准仅适用于以下设备:由全自动控制系统控制的燃气吸热式发动机； 制冷剂不直接接触的封闭系统制冷剂回路 待冷却或加热的流体；加热系统（加热水回路）的传热流体温度 正常运行期间不超过105°C；加热水回路（如已安装）的最大工作压力不超过6巴；生活热水回路（如已安装）不超过10巴。本欧洲标准仅适用于用于空间加热或空间冷却或 制冷，有或没有热量回收。冷凝器由空气和外部附加气体蒸发冷却的电器 本欧洲标准不包括水。本欧洲标准涵盖成套装置、单分裂和多分裂系统。单管 本欧洲标准涵盖了双风管机组。 上述设备可以具有一个或多个主要或次要功能。本欧洲标准适用于拟进行型式试验的电器。要求 对于未经型式试验的电器，需要进一步考虑。 对于成套装置（由多个部件组成），本欧洲标准仅适用于 作为一个完整的包装设计和供应。注:无论使用何种语言，本文中给出的所有符号都会被使用。交叉引用:EN 437EN 12102EN 16905-1prEN 16905-2EN 16905-3:2017813/2013/EU811/2013/EUEN 12309-4EN 14511-3EN 14825EN 15502-2-2:2014EN 16905-5:2017EN ISO 5167-1ISO 5167-1EN ISO 5801ISO 58012009/125/购买本文件时提供的所有现行修订均包括在内。

BS EN 16905-4:2017 specifies the requirements, test methods and test conditions for the rating and performance calculation of air conditioners and heat pumps using either air, water or brine as heat transfer media, with gas-fired endothermic engine driven compressors when used for space heating, cooling and refrigeration, hereafter referred to as "GEHP appliance".This European Standard only applies to appliances with a maximum heat input (based on net calorific value) not exceeding 70 kW at standard rating conditions.This European Standard only applies to appliances under categories I2H, I2E, I2Er, I2R, I2E(S)B, I2L, I2LL, I2ELL, I2E(R)B, I2ESi, I2E(R), I3P, I3B, I3B/P, II2H3+, II2Er3+, II2H3B/P, II2L3B/P, II2E3B/P, II2ELL3B/P, II2L3P, II2H3P, II2E3P and II2Er3P according to EN 437.This European Standard only applies to appliances having:gas fired endothermic engines under the control of fully automatic control systems;closed system refrigerant circuits in which the refrigerant does not come into direct contact with the fluid to be cooled or heated;where the temperature of the heat transfer fluid of the heating system (heating water circuit) does not exceed 105 °C during normal operation;where the maximum operating pressure in the:heating water circuit (if installed) does not exceed 6 bar;domestic hot water circuit (if installed) does not exceed 10 bar.This European Standard applies to appliances only when used for space heating or space cooling or for refrigeration, with or without heat recovery.The appliances having their condenser cooled by air and by the evaporation of external additional water are not covered by this European Standard.Packaged units, single split and multisplit systems are covered by this European Standard. Single duct and double duct units are covered by this European Standard.The above appliances can have one or more primary or secondary functions.This European Standard is applicable to appliances that are intended to be type tested. Requirements for appliances that are not type tested would need to be subject to further consideration. In the case of packaged units (consisting of several parts), this European Standard applies only to those designed and supplied as a complete package.NOTE All the symbols given in this text are used regardless of the language used.Cross References:EN 437EN 12102EN 16905-1prEN 16905-2EN 16905-3:2017813/2013/EU811/2013/EUEN 12309-4EN 14511-3EN 14825EN 15502-2-2:2014EN 16905-5:2017EN ISO 5167-1ISO 5167-1EN ISO 5801ISO 58012009/125/ECAll current amendments available at time of purchase are included with the purchase of this document.