范围:本标准规定了无卤电缆的设计、尺寸和试验要求 挤压绝缘和护套，额定电压高达450/750 V，适用于挠性电缆 在供电点或供电点之间供电的恶劣条件下的应用 充电站和电动汽车（EV）。 电动汽车充电电缆用于供电和通信（详情请参见 EN 61851-1和EN 62196系列）适用于电动汽车。充电电缆适用于以下情况: EN 61851-1中的充电模式1-3。本标准中额定电压为300/500 V的电缆仅适用于 允许用于EN 61851-1的充电模式1。 本标准中电缆的最高导体工作温度为90摄氏度。 本标准涵盖的电缆被理解为纯电缆，无例外 组件，无任何附件或插头。他们可能是 a） 车辆不可分割的一部分（EN 61851-1中的情况a）；或 b） 带车辆连接器和交流电源连接的可拆卸电缆总成的电缆部分 至插座（EN 61851-1的情况B）；或 c） 永久连接至固定充电点（EN 61851-1中的情况c）。 本标准描述了在安装和/或安装时确保安全性和可靠性的电缆 根据EN 50565-1和附录B的使用指南使用。交叉引用:IEC 61851-1EN 60811-508EN 61851-1IEC 60811-508IEC 60332-1-2:2004/AMD1:2015HD 308 S2:2001EN 50289-4-17:2015EN 50525-1:2011IEC 60811-404:2012IEC 60811-403:2012ISO 14572:2011EN 60811-401:2012EN 50395:2005EN 60811-404:2012EN 590: 2013IEC 60811-509:2012EN 60811-505:2012EN 228:2012ISO 22241-1:2006EN 60811-503:2012EN 60811-506:2012ISO 48:2010IEC 60228:2004IEC 60719:1992IEC 60811-504:2012IEC 60811-506:2012EN 62230:2007EN 50289-1-5:2001EN 60811-507:2012EN 60811-509:2012EN 60560811-503:2012IEC 60811-507:2012IEC 62230:2006EN 60228:2005IEC 60811-401:2012EN 62196-2:2017IEC 62196-2:2016ISO 4892-1:2016EN 62196-2:2012/A12: 2014EN 50565-1:2014IEC 60364-7-722:2015ISO 4892-2:2013EN ISO 4892-1（ISO 4892-1:2016）ASIEC 60445:2010HD 60364-7-718（IEC 60364-7-718:2011）ASEN ISO 4892-2:2013EN 60445:2010包含以下内容:修订，2019年5月

Scope: This standard specifies design, dimensions and test requirements for halogen-free cables with extruded insulation and sheath having a voltage rating of up to and including 450/750 V for flexible applications under severe condition for the power supply between the electricity supply point or the charging station and the electric vehicle (EV). The EV charging cable is intended to supply power and if needed communication (details see EN 61851-1 and the EN 62196 series) to an electric vehicle. The charging cables are applicable for charging modes 1-3 of EN 61851-1. The cables in this standard with rated voltage 300/500 V are only permitted for charging mode 1 of EN 61851-1. The maximum conductor operating temperatures for the cables in this standard is 90 °C. Cables, covered by this standard are understood without exception to be the pure cable component, without any kind of accessories or plugs. They may be a) an integral part of the vehicle (case A of EN 61851-1); or b) the cable part of a detachable cable assembly with a vehicle connector and AC supply connection to a socket outlet (case B of EN 61851-1); or, c) permanently attached to a fixed charging point (case C of EN 61851-1). This standard describes cables whose safety and reliability is ensured when they are installed and/or used in accordance to the guide to use EN 50565-1 and Annex B.Cross References:IEC 61851-1EN 60811-508EN 61851-1IEC 60811-508IEC 60332-1-2:2004/AMD1:2015HD 308 S2:2001EN 50289-4-17:2015EN 50525-1:2011IEC 60811-404:2012IEC 60811-403:2012ISO 14572:2011EN 60811-401:2012EN 50395:2005EN 60811-404:2012EN 590:2013IEC 60811-509:2012EN 60811-505:2012EN 228:2012ISO 22241-1:2006EN 60811-503:2012EN 60811-506:2012ISO 48:2010IEC 60228:2004IEC 60719:1992IEC 60811-504:2012IEC 60811-506:2012EN 62230:2007EN 50289-1-5:2001EN 60811-507:2012EN 60811-509:2012HD 605 S2:2008EN 50334:2001EN 60811-504:2012EN 60811-403:2012EN 60332-1-2:2004IEC 60811-505:2012IEC 60811-501:2012EN 60811-501:2012EN 50396:2005IEC 60811-503:2012IEC 60811-507:2012IEC 62230:2006EN 60228:2005IEC 60811-401:2012EN 62196-2:2017IEC 62196-2:2016ISO 4892-1:2016EN 62196-2:2012/A12:2014EN 50565-1:2014IEC 60364-7-722:2015ISO 4892-2:2013EN ISO 4892-1 (ISO 4892-1:2016) ASIEC 60445:2010HD 60364-7-718 (IEC 60364-7-718:2011) ASEN ISO 4892-2:2013EN 60445:2010Incorporates the following:Amendment, May 2019