IEC 62196-6:2022-插头、插座、车辆连接器和车辆插孔.电动汽车的传导充电.第6部分:用于直流电动汽车供电设备的直流插脚和接触管车辆耦合器的尺寸兼容性要求其中保护依赖于电气隔离-国家数字标准馆

现行 IEC 62196-6:2022

到馆阅读

收藏跟踪

购买正版

Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 6: Dimensional compatibility requirements for DC pin and contact-tube vehicle couplers intended to be used for DC EV supply equipment where protection relies on electrical separation 插头、插座、车辆连接器和车辆插孔.电动汽车的传导充电.第6部分:用于直流电动汽车供电设备的直流插脚和接触管车辆耦合器的尺寸兼容性要求其中保护依赖于电气隔离

发布日期： 2022-04-22

                IEC 62196-6:2022适用于电动汽车（EV）的车辆连接器、车辆插孔和电缆组件，用于包含控制装置的导电充电系统，额定工作电压高达120 V DC，额定电流高达100 a
根据IEC 61851-25:2020，这些附件用于导电充电系统的直流接口。

IEC 62196-6:2022 is applicable to vehicle connectors, vehicle inlets and cable assemblies for electric vehicle (EV), intended for use in conductive charging systems which incorporate control means, with a rated operating voltage up to 120 V DC and rated current up to 100 A.

These accessories are intended to be used for a DC interface of the conductive charging system according to IEC 61851-25:2020.

分类信息

发布单位或类别：国际组织-国际电工委员会

ICS分类： 43.120道路车辆工程 - 电车、 29.120.30电工器件 - 插头、插座、连接器

关联关系

研制信息

归口单位： TC 23/SC 23H

相似标准/计划/法规

KS R IEC 62196-1

플러그, 소켓-아웃렛, 자동차 커넥터 및 자동차 인렛 — 전기자동차의 전도성 충전 — 제1부: 일반 요구사항
插头、插座、车辆连接器和车辆插座电动车辆的导电充电第1部分:一般要求

KS R IEC 62196-1(2020 Confirm)

플러그, 소켓-아웃렛, 자동차 커넥터 및 자동차 인렛 — 전기자동차의 전도성 충전 — 제1부: 일반 요구사항
插头插座车辆连接器和车辆入口 - 电动车辆的导电充电第1部分:一般要求

IEC 62196-1-2022

Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements
插头、插座、车辆连接器和车辆插孔.电动车辆的传导充电.第1部分:一般要求

IEC 62196-1-2022 CMV

Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements
插头、插座、车辆连接器和车辆插孔.电动车辆的传导充电.第1部分:一般要求

GOST R IEC 62196-1-2013

Вилки, штепсельные розетки, соединители и вводы для транспортных средств. Кондуктивная зарядка для электромобилей. Часть 1. Общие требования
插头插座连接器和套管的车辆传导充电的电动汽车第1部分:通用要求

BS PD IEC TS 62196-3-1-2020

Plugs, socket-outlets, vehicle connectors and vehicle inlets. Conductive charging of electric vehicles-Vehicle connector, vehicle inlet and cable assembly for DC charging intended to be used with a thermal management system
插头、插座、车辆连接器和车辆插孔电动汽车的传导充电

KS R IEC TS 62196-3-1

플러그, 소켓-아웃렛, 자동차 커넥터 및 자동차 인렛 — 전기자동차의 전도성 충전 — 제3-1부: 열관리시스템과 같이 사용하기 위한 직류 충전용 자동차 커넥터, 자동차 인렛 및 케이블 어셈블리
插头插座车辆连接器和车辆插孔.电动车辆的传导充电.第3-1部分:与热管理系统一起使用的直流充电用车辆连接器车辆插孔和电缆组件

IEC TS 62196-3-1-2020

Plugs,socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 3-1: Vehicle connector, vehicle inlet and cable assembly for DC charging intended to be used with a thermal management system
插头、插座、车辆连接器和车辆插孔.电动汽车的传导充电.第3-1部分:与热管理系统一起使用的直流充电用车辆连接器、车辆插孔和电缆组件

IEC PAS 63472-2023

Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Dimensional compatibility description for configuration FF AC/DC contact-tube vehicle coupler
插头、插座、车辆连接器和车辆插孔电动车辆的传导充电 FF AC/DC接触管车辆耦合器配置的尺寸兼容性描述

KS R IEC 62196-2

플러그, 소켓-아웃렛, 자동차 커넥터 및 자동차 인렛 — 전기자동차의 전도성 충전 — 제2부: 교류 핀과 접촉 튜브 부속품에 대한 치수 적합성 요구사항
插头、插座、车辆连接器和车辆插座电动车辆的导电充电第2部分:交流插针和接触管附件的尺寸兼容性要求

IEC 62196-2-2022

Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility requirements for AC pin and contact-tube accessories
插头、插座、车辆连接器和车辆插座.电动车辆的导电充电.第2部分:交流插脚和接触管附件的尺寸兼容性要求

KS R IEC 62196-2

플러그, 소켓-아웃렛, 자동차 커넥터 및 자동차 인렛 — 전기자동차의 전도성 충전 — 제2부: 교류 핀과 접촉 튜브 부속품에 대한 치수 적합성 및 상호 호환성 요구사항
插头插座插座车辆连接器和车辆入口 - 电动车辆的导电充电 - 第2部分:尺寸兼容性和互换性要求对于A.C.针和接触管配件

KS R IEC 62196-3

플러그, 소켓-아웃렛, 자동차 커넥터 및 자동차 인렛 — 전기자동차의 전도성 충전 — 제3부: 직류 및 교류/직류 핀과 접촉 튜브 자동차 커플러에 대한 치수 적합성 요구사항
插头、插座、车辆连接器和车辆插座电动车辆的导电充电第3部分:直流和交流/直流插针和接触管车辆耦合器的尺寸兼容性要求

IEC 62196-3-2022

Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 3: Dimensional compatibility requirements for DC and AC/DC pin and contact-tube vehicle couplers
插头、插座、车辆连接器和车辆插座.电动车辆的导电充电.第3部分:直流和交流/直流插针和接触管车辆耦合器的尺寸兼容性要求

VDE 0623-5-1/A11-2013/DIN EN 62196-1/A11

Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements; German version EN 62196-1:2012/A11:2013
插头、插座、车辆连接器和车辆插孔.电动汽车的传导充电.第1部分:一般要求；德文版EN 62196-1:2012/A11:2013

UNE-EN 62196-1-2004

Plugs, socket-outlets, vehicle couplers and vehicle inlets - Conductive charging of electric vehicles -- Part 1: Charging of electric vehicles up to 250 A a.c. and 400 A d.c.
插头、插座、车辆耦合器和车辆插孔.电动汽车的传导充电.第1部分:交流250A和直流400A以下电动汽车的充电

KS R IEC 62196-3

플러그, 소켓-아웃렛, 자동차 커넥터 및 자동차 인렛?전기자동차의 전도성 충전?제3부: 직류 및 교류/직류 핀과 접촉 튜브 자동차 커플러에 대한 치수 적합성 및 상호 호환성 요구사항
插头插座车辆连接器和车辆入口 - 电动车辆的导电充电第3部分:直流的尺寸兼容性和互换性要求和A.c./d.c 销和接触管车辆耦合器

KS R IEC 62196-3(2022 Confirm)

플러그, 소켓-아웃렛, 자동차 커넥터 및 자동차 인렛?전기자동차의 전도성 충전?제3부: 직류 및 교류/직류 핀과 접촉 튜브 자동차 커플러에 대한 치수 적합성 및 상호 호환성 요구사항
插头、插座、车辆连接器和车辆插孔.电动车辆的传导充电.第3部分:直流和交流/直流插针和接触管车辆耦合器的尺寸兼容性和互换性要求

DIN EN 62196-1/A1-DRAFT

Draft Document - Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements (IEC 23H/389A/CD:2017); Text in German and English
文件草案——插头、插座、车辆连接器和车辆插孔——电动汽车的传导充电——第1部分:一般要求（IEC 23H/389A/CD:2017）；德语和英语文本

DIN EN 62196-1-100-DRAFT

Draft Document - Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements; German version EN 62196-1:2012/FprAA:2012
起草文件——插头、插座、车辆连接器和车辆插孔——电动汽车的传导充电——第1部分:一般要求；德文版EN 62196-1:2012/FprAA:2012

《国家标准化发展纲要》提出建设国家数字标准馆，推动标准化工作向数字化、网络化、智能化转型。中国标准化研究院正在全力推进国家数字标准馆建设，力争在2026年底建成“一个中心”和“一个平台”，即全球领先的标准数据资源中心，涵盖标准全生命周期的数字化、网络化、智能化研究与服务平台。

关于我们

查新颖性

查有效性

跟踪标准

比对标准

专题数据库

标准管理系统

大数据分析系统

标准智能研制系统