1.1 本试验方法包括制备和测试实验室压实沥青混合料试样的程序，以测量水对铺路混合料抗拉强度的影响。本试验方法适用于密实混合料，如规范中沥青路面混合料组成表中所示的混合料 第515页 该试验方法可用于评估含或不含抗剥落添加剂（包括液体和粉状固体，如熟石灰或波特兰水泥）的水分的影响。 1.2 括号中以国际单位制或英寸磅单位表示的数值应单独视为标准值。每个系统中的值可能不完全相等；因此，必须独立使用每个系统，而不以任何方式组合值。 1.3 本标准的文本引用了提供说明材料的注释和脚注。这些注释和脚注（不包括表和图中的注释和脚注）不应视为本标准的要求。 1.4 本标准并不旨在解决与其使用相关的所有安全问题（如有）。 本标准的使用者有责任在使用前建立适当的安全、健康和环境实践，并确定监管限制的适用性。 1.5 本国际标准是根据世界贸易组织技术性贸易壁垒（TBT）委员会发布的《国际标准、指南和建议制定原则决定》中确立的国际公认标准化原则制定的。 =====意义和用途====== 5.1 该试验方法可用于测试沥青混合料以及混合料设计试验，以确定水分损害的可能性，确定抗剥落添加剂是否有效，并确定最大化效力所需的添加剂剂量。该测试方法也可用于测试工厂生产的混合物，以确定添加剂在现场施加条件下的有效性。 注1: 本标准产生的结果质量取决于执行程序的人员的能力以及所用设备的能力、校准和维护。符合规范标准的机构 第3666页 通常认为能够进行合格和客观的测试、取样、检验等。本标准的用户应注意遵守规范 第3666页 单独使用并不能完全确保可靠的结果。可靠的结果取决于许多因素； 遵循规范的建议 第3666页 或一些类似的可接受准则提供了评估和控制这些因素的方法。

1.1 This test method covers procedures for preparing and testing laboratory-compacted asphalt mixture specimens for the purpose of measuring the effect of water on the tensile strength of the paving mixture. This test method is applicable to dense mixtures such as those appearing in the Table for Composition of Bituminous Paving Mixtures in Specification D3515 . This test method can be used to evaluate the effect of moisture with or without antistripping additives including liquids and pulverulent solids such as hydrated lime or portland cement. 1.2 The values stated in either SI units or inch-pound units in brackets shall be regarded separately as standard. The values in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values in any way. 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 5.1 This test method can be used to test asphalt mixtures in conjunction with mixture design testing to determine the potential for moisture damage, to determine whether or not an antistripping additive is effective, and to determine what dosage of an additive is needed to maximize the effectiveness. This test method can also be used to test mixtures produced in plants to determine the effectiveness of additives under the conditions imposed in the field. Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.