首页 馆藏资源 舆情信息 标准服务 科研活动 关于我们
现行 ASTM D3517-24
到馆提醒
收藏跟踪
购买正版
Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe “玻璃纤维”(玻璃纤维增强热固性树脂)压力管的标准规范
发布日期: 2024-05-01
1.1 本规范涵盖8英寸(200 mm)至156英寸(4000 mm)的机制玻璃纤维管,用于内部表压小于等于450 psi(3103 kPa)的输水系统。玻璃纤维增强热固性树脂管(RTRP)和玻璃纤维增强聚合物砂浆管(RPMP)均为玻璃纤维管。该标准主要适用于埋地应用中安装的管道,但也可在适用于其他安装的范围内使用,如但不限于现有管道的顶管、隧道衬砌和滑动衬砌修复。 注1: 就本标准而言,聚合物不包括天然聚合物。 1.2 以英寸磅为单位的数值应视为标准。括号中给出的值仅供参考。 注2: 目前还没有与该标准等效的ISO。 1.3 以下安全隐患警告仅适用于第节测试方法部分 8. ,本规范的: 本标准并不旨在解决与其使用相关的所有安全问题(如有)。本标准的使用者有责任在使用前制定适当的安全、健康和环境实践,并确定监管限制的适用性。 1.4 本国际标准是根据世界贸易组织技术性贸易壁垒委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认的标准化原则制定的。
1.1 This specification covers machine-made fiberglass pipe, 8 in. (200 mm) through 156 in. (4000 mm), intended for use in water conveyance systems which operate at internal gage pressures of 450 psi (3103 kPa) or less. Both glass-fiber-reinforced thermosetting-resin pipe (RTRP) and glass-fiber-reinforced polymer mortar pipe (RPMP) are fiberglass pipes. The standard is suited primarily for pipes to be installed in buried applications, although it is acceptable to be used to the extent applicable for other installations such as, but not limited to, jacking, tunnel lining and slip-lining rehabilitation of existing pipelines. Note 1: For the purposes of this standard, polymer does not include natural polymers. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information purposes only. Note 2: There is no known ISO equivalent to this standard. 1.3 The following safety hazards caveat pertains only to the test methods portion, Section 8 , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
分类信息
关联关系
研制信息
归口单位: D20.23
相似标准/计划/法规
现行
ASTM D3753-20
Standard Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Manholes and Wetwells
玻璃纤维(玻璃纤维增强热固性树脂)检修孔和湿井的标准规范
2020-12-01
现行
ASTM D5421-23
Standard Specification for Contact Molded “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Flanges
接触模压“玻璃纤维”(玻璃纤维增强热固性树脂)法兰的标准规范
2023-05-01
现行
ASTM D4024-22
Standard Specification for Machine Made “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Flanges
机械制造的“玻璃纤维”(玻璃纤维增强热固性树脂)法兰的标准规范
2022-07-01
现行
ASTM D3982-21
Standard Specification for Contact Molded “Fiberglass” (Glass Fiber Reinforced Thermosetting Resin) Ducts
接触模制“玻璃纤维”(玻璃纤维增强热固性树脂)管道的标准规范
2021-04-01
现行
ASTM D2997-21
Standard Specification for Centrifugally Cast “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
离心铸造“玻璃纤维”(玻璃纤维增强热固性树脂)管的标准规范
2021-05-01
现行
ASTM D2996-23
Standard Specification for Filament-Wound “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
纤维缠绕“玻璃纤维”(玻璃纤维增强热固性树脂)管的标准规范
2023-10-01
现行
ASTM D3754-24
Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer and Industrial Pressure Pipe
“玻璃纤维”(玻璃纤维增强热固性树脂)下水道和工业压力管的标准规范
2024-08-01
现行
ASTM D3840-24
Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Fittings for Nonpressure Applications
非压力应用的“玻璃纤维”(玻璃纤维增强热固性树脂)管件标准规范
2024-08-01
现行
ASTM D3262-20
Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer Pipe
标准规格
2020-03-01
现行
ASTM D5685-19
Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe Fittings
“;玻璃纤维&x201d(玻璃纤维增强热固性树脂)压力管件
2019-04-01
现行
ASTM D4161-24
Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Joints Using Flexible Elastomeric Seals
使用柔性弹性密封件的“玻璃纤维”(玻璃纤维增强热固性树脂)管接头的标准规范
2024-08-15
现行
ASTM D6041-23
Standard Specification for Contact-Molded “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Corrosion Resistant Pipe and Fittings
接触模压“玻璃纤维”(玻璃纤维增强热固性树脂)耐腐蚀管道和配件的标准规范
2023-08-01
现行
ASTM D3567-17(2022)
Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
测定“玻璃纤维”(玻璃纤维增强热固性树脂)管和配件尺寸的标准实施规程
2022-05-01
现行
ASTM D3839-14(2019)
Standard Guide for Underground Installation of “Fiberglass” (Glass-Fiber Reinforced Thermosetting-Resin) Pipe
“的地下安装标准指南;玻璃纤维&x201d(玻璃纤维增强热固性树脂管
2019-08-01
现行
ASTM C1355/C1355M-96(2020)
Standard Specification for Glass Fiber Reinforced Gypsum Composites
玻璃纤维增​​强石膏复合材料标准规范
2020-06-01
现行
ASTM D2924-24
Standard Test Method for External Pressure Resistance of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
“玻璃纤维”(玻璃纤维增强热固性树脂)管外部耐压性的标准试验方法
2024-02-01
现行
ASTM D3681-23
Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected Condition
偏转条件下“玻璃纤维”(玻璃纤维增强热固性树脂)管耐化学性的标准试验方法
2023-07-01
现行
ASTM C1381/C1381M-23
Standard Specification for Molded Glass Fiber Reinforced Gypsum Parts
模制玻璃纤维增强石膏部件的标准规范
2023-03-01
现行
ASTM D3841-21
Standard Specification for Glass-Fiber-Reinforced Polyester Plastic Panels
玻璃纤维增​​强聚酯塑料板标准规范
2021-05-01
现行
ASTM D2992-24
Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
获得“玻璃纤维”(玻璃纤维增强热固性树脂)管和配件的静水压或压力设计基础的标准实施规程
2024-06-01