BS ISO 13955:1997+A1:2020-塑料管道和配件聚乙烯（PE）电熔组件的破碎脱粘试验-国家数字标准馆

现行 BS ISO 13955:1997+A1:2020

到馆提醒

收藏跟踪

购买正版

Plastics pipes and fittings. Crushing decohesion test for polyethylene (PE) electrofusion assemblies 塑料管道和配件聚乙烯（PE）电熔组件的破碎脱粘试验

发布日期： 2020-05-04

本国际标准描述了一种用于测定流体分配用聚乙烯（PE）管和电熔插座或鞍座组件抗剥离性的压碎试验方法。该方法适用于标称外径在16 mm和225 mm之间的管道组件。购买本文件时可获得的所有当前修订均包含在购买本文件中。

This International Standard describes a crushing test method for determining the decohesive resistance of polyethylene (PE) pipe and electrofusion socket or saddle assemblies for use in the distribution of fluids. The method is applicable to assemblies with pipes of nominal outside diameter between 16 mm and 225 mm.All current amendments available at time of purchase are included with the purchase of this document.

分类信息

发布单位或类别：英国-英国标准学会

关联关系

研制信息

相似标准/计划/法规

Plastics pipes and fittings — Crushing decohesion test for polyethylene (PE) electrofusion assemblies
塑料管道和配件——聚乙烯（PE）电熔组件的破碎脱粘试验

GB/T 19806-2005

塑料管材和管件聚乙烯电熔组件的挤压剥离试验
Plastics pipes and fittings Crushing decohesion test for polyethylene(PE)electrofusion assemblies

ISO 13955-1997/Amd 1-2020

Plastics pipes and fittings — Crushing decohesion test for polyethylene (PE) electrofusion assemblies — Amendment 1
塑料管材和管件聚乙烯电熔组件的挤压剥离试验

Plastics pipes and fittings — Decohesion test of electrofusion assemblies — Strip-bend test
塑料管道和配件——电熔组件的脱粘试验——带材弯曲试验

BS ISO 21751-2011

Plastics pipes and fittings. Decohesion test of electrofusion assemblies. Strip-bend test
塑料管道和配件电熔组件的脱粘试验带材弯曲试验

Plastics pipes and fittings — Decohesion test of polyethylene (PE) saddle fusion joints — Evaluation of ductility of fusion joint interface by tear test
塑料管道和配件——聚乙烯（PE）鞍形熔合接头的脱粘试验——用撕裂试验评价熔合接头界面的延性

Plastics pipes and fittings — Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
塑料管道和配件——标称外径大于或等于90 mm的聚乙烯（PE）电熔组件的剥离剥离试验

BS ISO 13954-1997+A1-2020

Plastics pipes and fittings. Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
塑料管道和配件标称外径大于或等于90 mm的聚乙烯（PE）电熔组件的剥离剥离试验

GB/T 19808-2005

塑料管材和管件公称外径大于或等于90mm的聚乙烯电熔组件的拉伸剥离试验
Plastics pipes and fittings Peel decohesion test for polyethylene(PE)electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm

ISO 13954-1997/Amd 1-2020

Plastics pipes and fittings — Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm — Amendment 1
塑料管材和管件公称外径大于或等于90mm的聚乙烯（PE）电熔组件的剥离试验

Plastics pipes and fittings — Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion
塑料管道和配件——通过对接熔合制备聚乙烯（PE）管/管或管/管件试件组件

GB/T 19809-2005

塑料管材和管件聚乙烯（PE）管材/管材或管材/管件热熔对接组件的制备
Plastics pipes and fittings-Preparation of polyethylene(PE)pipe/pipe or pipe/fitting test piece assemblies by butt fusion

BS ISO 11414-2009

Plastics pipes and fittings. Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion
塑料管道和配件通过对接熔合制备聚乙烯（PE）管/管或管/管件试件组件

GOST R ISO 11414-2014

Трубы и фитинги пластмассовые. Подготовка контрольного образца соединения труба/труба или труба/фитинг из полиэтилена (ПЭ), выполненного сваркой встык
塑料管材及配件通过对接融合制备聚乙烯（PE）管/管或管/配件试件组件

Plastics pipes and fittings — Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting
塑料管件和配件 - 聚乙烯（Pe）管和电熔接头之间的试件组件的制备

BS ISO 11413-2019

Plastics pipes and fittings. Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting
塑料管道和配件聚乙烯（PE）管和电熔配件之间试件组件的制备

GB/T 19807-2005

塑料管材和管件聚乙烯管材和电熔管件组合试件的制备
Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene(PE)pipe and an electrofusion fitting

GB/T 19712-2005

塑料管材和管件聚乙烯（PE）鞍形旁通抗冲击试验方法
Plastics pipes and fittings Polyethylene(PE) tapping tees Test method for impact resistance

Plastics pipes and fittings — Polyethylene (PE) tapping tees — Test method for impact resistance
塑料管道和配件——聚乙烯（PE）开孔三通——抗冲击性试验方法

Plastics piping and ducting systems. Injection-moulded thermoplastics fittings for pressure piping systems. Test method for maximum deformation by crushing
塑料管道系统压力管道系统用注射成型热塑性塑料配件用压碎法测定最大变形的试验方法

《国家标准化发展纲要》提出建设国家数字标准馆，推动标准化工作向数字化、网络化、智能化转型。中国标准化研究院正在全力推进国家数字标准馆建设，力争在2026年底建成“一个中心”和“一个平台”，即全球领先的标准数据资源中心，涵盖标准全生命周期的数字化、网络化、智能化研究与服务平台。

专题数据库

标准管理系统

大数据分析系统

标准智能研制系统