1.1 这些表格列出了32-48号身材的年轻男性的身体尺寸。虽然这些都是身体测量值，但在考虑面料类型、身体运动的舒适性、造型和合身度等因素时，它们可以作为该尺寸范围内年轻男性服装设计的基准。 1.2 这些表格列出了所有年轻男性尺码的身体测量值。 1.3 以国际单位制或英寸-磅单位表示的数值应单独视为标准值。每个系统中规定的值不一定是精确的等价物；因此，为确保符合本标准，每个系统应独立使用，且两个系统的值不得组合。 1.4 本标准并非旨在解决与其使用相关的所有安全问题（如有）。 本标准的用户有责任在使用前制定适当的安全、健康和环境实践，并确定监管限制的适用性。 1.5 本国际标准是根据世界贸易组织技术性贸易壁垒（TBT）委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认标准化原则制定的。 ====意义和用途====== 4.1 身体测量信息的使用 表1 和 表2 将协助制造商开发符合感兴趣人群当前人体测量特征的图案和服装。反过来，这种做法应减少或尽量减少消费者对服装尺码的困惑和不满（另请参阅ISO 3635尺码指定程序）。 4.2 描述每个年轻男性尺寸的三维化身由Alvanon，股份有限公司创建，并包含在本标准中，以帮助制造商可视化由中的测量图表生成的姿势、形状和比例 表1 和 表2 . （参见 无花果。1- 6. .) 图1 形式前视图32-38 图2 形式前视图39-48 图3 窗体侧视图32-38 图4 表单侧视图39-48 图5 背面视图32-38 图6 背面视图39-48

1.1 These tables list body measurements of young men figure type sizes 32-48. Although these are body measurements, they can be used as a baseline in designing apparel for young men in this size range when considering such factors as fabric type, ease for body movement, styling, and fit. 1.2 These tables list body measurements for the complete range of young men sizing. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 4.1 The use of the body measurement information in Table 1 and Table 2 will assist manufacturers in developing patterns and garments that are consistent with the current anthropometric characteristics of the population of interest. This practice should, in turn, reduce or minimize consumer confusion and dissatisfaction related to apparel sizing (also refer to ISO 3635 Size Designation Procedures). 4.2 Three-dimensional avatars depicting each of the young men sizes were created by Alvanon, Inc. and included in this standard to assist manufacturers in visualizing the posture, shape, and proportions generated by the measurements charts in Table 1 and Table 2 . (See Figs. 1- 6 .) FIG. 1 Form Front View 32-38 FIG. 2 Form Front View 39-48 FIG. 3 Form Side View 32-38 FIG. 4 Form Side View 39-48 FIG. 5 Form Back View 32-38 FIG. 6 Form Back View 39-48