1.1 本试验方法涵盖压敏标签纸的剥离附着力测量。本试验方法提供了对压敏标签纸与标准钢基材或其他相关表面粘附性的测量。 1.2 本试验方法提供了一种评估给定类型压敏标签纸粘附均匀性的方法。评估可以在板材或卷内、板材或卷之间或生产批次之间进行。 1.3 标签纸和粘合剂的变化会影响响应；因此，该测试方法不能用于确定不均匀性的具体原因。 1.4 本试验方法可能不适用于测试具有硬背衬或背衬在低力下表现出高拉伸的标签纸。这些特性可能导致测试响应的高可变性，这并不能真实反映粘合剂的真实性质。 1.5 以国际单位制或英寸-磅单位表示的数值应单独视为标准。每个系统中规定的值可能不是精确的等效值；因此，每个系统必须独立使用，不得以任何方式组合值。 1.6 本标准并非旨在解决与其使用相关的所有安全问题（如有）。本标准的用户有责任在使用前制定适当的安全、健康和环境实践，并确定监管限制的适用性。 1.7 本国际标准是根据世界贸易组织技术性贸易壁垒（TBT）委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认标准化原则制定的。 ====意义和用途====== 5.1 本测试方法是用于质量保证的工具。 考虑到压敏标签材料和该标签材料预期的最小或最大剥离附着力值的要求，测试数据可与验收标准结合使用。 5.2 与标准不锈钢板相比，该测试方法可以显示给定标签材料与不同材料和纹理的一个或多个表面的相对粘合强度。本程序可接受用代表拟议基板的面板替代标准不锈钢面板。

1.1 This test method covers the measurement of the peel adhesion of pressure-sensitive label stocks. This test method gives a measure of the adherence to a standard steel substrate or to other surfaces of interest for a pressure-sensitive label stock. 1.2 This test method provides a means of assessing the uniformity of the adhesion of a given type of pressure-sensitive label stock. The assessment may be within a sheet or roll, between sheets or rolls, or between production lots. 1.3 Variations in the label stock facestock and adhesive can affect the response; therefore, this test method cannot be used to pinpoint the specific cause(s) of nonuniformity. 1.4 This test method may not be appropriate to test label stocks having either stiff backings or backings showing a high stretch at low forces. These characteristics could result in a high variability of the test response, which is not a true indication of the real nature of the adhesive bond. 1.5 The values stated in either SI or inch-pound units are to be regarded separately as the standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently, without combining values in any way. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 5.1 This test method is a tool for quality assurance use. Given a pressure-sensitive label stock and a requirement in terms of the minimum or maximum peel adhesion value expected for this label stock, the data from the test can be used in conjunction with acceptance criteria. 5.2 This test method can show the relative bond strength of a given label stock to one or more surfaces of varied material and texture as compared to the standard stainless steel panel. Substitution of panels representative of the proposed substrates for the standard stainless steel panel would be acceptable for this procedure.