1.1 本规程适用于轨道轨距大于或等于12英寸（305毫米）的游乐铁路游乐设施的操作，轨道轨距在轨道头部之间测量。这不包括专门为儿童设计的顾客动力乘坐车辆。 1.2 本标准不适用于类似铁路的过山车等游乐设施的操作，但属于实施规程的范围 F2291 -22a或练习 F1159美元 -16个 ε1 本标准也不适用于ANSI B77.2-20或BS EN 1907-17中定义的缆车。 1.3 本标准不适用于用作便携式游乐设施或游乐设施的铁路游乐设施操作。 1.4 本标准不适用于永久安装的娱乐铁路游乐设施和旅游铁路及其相关轨道、装置和设施，这些轨道、装置或设施全部或部分由联邦铁路管理局（FRA）或国家同等机构管辖。 1. 5. 以英寸磅为单位的数值应视为标准。括号中给出的值是国际单位制的数学转换，仅供参考，不被视为标准。 1.6 本标准并非旨在解决与其使用相关的所有安全问题（如有）。本标准的使用者有责任在使用前制定适当的安全、健康和环境实践，并确定监管限制的适用性。 1.7 本国际标准是根据世界贸易组织技术性贸易壁垒委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认的标准化原则制定的。 ====意义和用途====== 4.1 本规程的目的是为铁路游乐设施的操作划定信息并制定程序。 4.2 本标准的使用者应审查并遵守小节中引用的“核心”ASTM委员会F24标准 2.1 本标准。本标准可能要求对这些标准进行修改或替代要求。

1.1 This practice applies to operations of amusement railway ride(s) that have a track gauge greater than or equal to 12 in. (305 mm) measured between the heads of the rails. This excludes patron powered ride vehicles specifically designed for children. 1.2 This standard does not apply to the operation of rides, such as roller coasters, that resemble railways, but fall within the scope of Practice F2291 -22a or Practice F1159 -16 ε1 . This standard also does not apply to funiculars as defined in ANSI B77.2-20 or BS EN 1907-17. 1.3 This standard does not apply to amusement railway rides operation that are intended for use as a portable amusement ride or attraction. 1.4 This standard does not apply to permanently installed amusement railway rides and tourist railways, and their associated track, devices and facilities that are under the jurisdiction of the Federal Railroad Administration (FRA) in whole or part or national equivalent. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ====== 4.1 The purpose of this practice is to delineate information and to establish procedures for the operation of an amusement railway ride. 4.2 The user of this standard shall be required to review and comply with the referenced “core” ASTM Committee F24 standards in Subsection 2.1 of this standard. Modified or alternate requirements to those standards may be required in this standard.